RF OWNERS CLUB

What about posting on FB for scrap parts? MIght get you something.

Old wobbler wrote:What about posting on FB for scrap parts? MIght get you something.

I don't do FB mate, hate it with a passion !

No local breakers your way mate ?

https://rover.ebay.com/rover/0/0/0?mpre ... 2658973922

Gotta spend money to make money

https://rover.ebay.com/rover/0/0/0?mpre ... 1466031880

This bloke got 2 bandit 6 cranks for £20 each

Actually he got loads cranks at 20 or best offer I’d be tempted to message him for a bundle price see if can do 6 for100 quid delivered or something.

I'm not doing it to make a fortune, its more something to do than anything else mate but cranks at 20 quid kills my small profit

I'll either have to put my prices up a lot or find a cheap supply of busted engines

Must be selling them very cheap then mate.

mike-rf600r wrote:Must be selling them very cheap then mate.

Yes mate, way too cheap but they are going as quick as I can make them & I'm not having to stick them on ebay or advertise elsewhere which is worth a couple of quid to me

I'm only making about 20 quid out of the stools, its a lot of work for that but I enjoy it

Ok well I’ll hate fine i do the same with exhausts sometimes. Often make small amounts on them but I turn them around soon as I get them so a quick 20-40 quid is great. Few of those soon adds up

However just saying don’t do yourself out of dosh especially if money tight. Don’t be too expensive but being too cheap is just as bad at times.

Keep up the good work thoUgh. :ymapplause:

Cheers mike I knew you would get it mate :-bd

I did the first one & a guy made an offer on it, I thought that's ok as it wasn't all that good, the next ones were much better but the precedent on price had been set & they shift fairly quickly so I'm happy enough

If I had enough scrap engines I could do it as a production line & cut down on the time spent a great deal but its not going to happen lol

Having said that I have one bigger ticket item almost done & that's cost not a lot in terms of parts, I hope to get a decent amount for my time on that & I have a couple of ideas for stuff I can make from all the leftover bits that will also only cost my time so I should see a few quid in the end

slim wrote:

Old wobbler wrote:What about posting on FB for scrap parts? MIght get you something.

I don't do FB mate, hate it with a passion !

Well that told me.

What sort of engine bits do you want, slim?

Cranks, camshafts, valves, holed pistons?

Old wobbler wrote:What sort of engine bits do you want, slim?

Cranks, camshafts, valves, holed pistons?

Its mainly cranks & rods I am short of at the minute mate, cams, balancer shafts & any gearbox parts are always useful though

Pretty much anything steel & interesting shaped comes in useful eventually, I have even used old sprockets a few times now

Something different

Stuck this on ebay to make way for the next thing I started making today

:-bd

Would you believe I just sold it I got an offer I couldn't refuse so well happy

Onwards & upwards with the next thing

slim wrote:Would you believe I just sold it I got an offer I couldn't refuse so well happy

Onwards & upwards with the next thing

Well done sir. I hope you actually started pricing things near the going rate this time. B-)

mike-rf600r wrote:

slim wrote:Would you believe I just sold it I got an offer I couldn't refuse so well happy

Onwards & upwards with the next thing

Well done sir. I hope you actually started pricing things near the going rate this time. B-)

I stuck it on ebay at 100 quid start price, a mate spotted it, knew from the user name was me & phoned me up with a good offer to remove it, job done & no ebay fees

Nice. That’s why I couldn’t find it under sold items then )

Nice work :-bd

Today I finished up the legs for my GSXR engine block coffee table & made the top which was a real pain in the arse

Tomorrow I will be mainly sanding & varnishing the top & that will be another item ready for sale in a few days, pics when its done

:ymapplause: that should sell well! Tables tend to in that style.

mike-rf600r wrote::ymapplause: that should sell well! Tables tend to in that style.

This is done differently to the ones you will have seen Mike, I don't like to copy other peoples stuff

Difficult to explain what I have done but its two 1052 slabby blocks with the liners as legs & supports + a wooden top, show you in a couple of days mate, i'll be interested to know what you think :-bd